12f683 problem

[Fabricio]

Hi, i am using the pic 12f683, ccs 3.190 and winpic800. I can read, verify and erase the microcontroller, but when i try to programme it gives me an error in direc 0x0000.
My code is:
#include <12F683.h>
#use delay(clock=8000000)
#fuses NOWDT,INTRC_IO, NOCPD, NOPROTECT, MCLR, NOPUT, NOBROWNOUT, IESO, NOFCMEN

#use rs232(baud=9600,parity=N,xmit=PIN_A0,rcv=PIN_A1,bits=8)
#byte OSCCON = 0x8F

long rise;
#int_RA
RA3_isr()
{
rise = get_timer1();
set_timer1(0);

}


void main()
{

set_tris_a(0b001010);
OSCCON = 0x71; // Setup for 8 MHz with internal oscillator (*)
//setup_oscillator(OSC_8MHZ); // select 8MHz internal clock(*)
setup_timer_1(T1_INTERNAL|T1_DIV_BY_1);
setup_comparator(NC_NC_NC_NC);
enable_interrupts(INT_RA3);
enable_interrupts(GLOBAL);
while (1)
{
delay_ms(2000);
printf("%lu\n\r",rise);
rise=0;
}
}
(*) I have proved both options.


Any idea??
thanks. greetings

[Fabricio]

problem solved, it was an error of configuration of the winpic
my problem now is that I set:
#use rs232 (baud=9600, parity=N, xmit=PIN_A0, rcv=PIN_A1, bits=8, restart_wdt)
but in the hyperterminal, the correct configuration is
4800.
Is it a problem of the clock??

[ckielstra]

[Fabricio]

new problem.
I used the restart_cause() funtion and it give me: NORMAL_POWER_UP 24.

My output is:
START
Restart=24
START
Restart=24
START
Restart=24
START
Restart=24
(reset continually) but when i put an signal in GP2(CCP1 in), the interruption is executed and prints 'XXXXXXXX......
Where is my error?
my code is:

#include <12F683.h>
#device adc=8
#use delay(clock=4000000)
#fuses WDT,INTRC_IO, NOCPD, NOPROTECT, NOMCLR, NOPUT, NOBROWNOUT, NOIESO, NOFCMEN
#use rs232(baud=9600,parity=N,xmit=PIN_A0,rcv=PIN_A1,bits=8,restart_wdt,errors)
#ROM 0x7FF={0x3400}

long rise;
//--------------------------------
#int_CCP1
CCP1_isr()
{
putc('X');
}

//---------------------------------
void Constructor (void);

void main()
{
long aux;
restart_wdt();
aux=restart_cause();
printf("Restart=%lu\n\r",aux);
printf("START\n\r");
Constructor ();

while (1)
{
restart_wdt();
printf("do something\r");
delay_ms(2000);
//rise=0;
}
}
//-----------------------------------------------
void Constructor (void)
{
restart_wdt();
set_tris_a(0b001110);
#ASM
movlw 0x8f// OSCCON
movwf 0x04
movlw 0b1100101// 4M, intternal clock, stable
movwf 0x00

movlw 0x90// OSCTUNE – OSCILLATOR TUNING
movwf 0x04
movlw 0b00000//
movwf 0x00

movlw 0x81// OPTION REG
movwf 0x04
movlw 0b11001000 // pull up dis,prescaler a wdt
movwf 0x00

movlw 0x8C// PIE1 periph interrup enable
movwf 0x04
movlw 0b00100000 // CCP1 enable
movwf 0x00

movlw 0x15//CCP1CON CCP control reg
movwf 0x04
movlw 0b00000101
movwf 0x00

movlw 0x10//T1CON
movwf 0x04
movlw 0b00000001
movwf 0x00


movlw 0x2007 // config
movwf 0x04
movlw 0b11000011011100 //
movwf 0x00

#ENDASM

setup_adc_ports(0);
setup_adc(ADC_OFF);
//setup_counters(RTCC_INTERNAL,RTCC_DIV_1);
//setup_timer_1(T1_INTERNAL|T1_DIV_BY_1);
setup_timer_2(T2_DISABLED,0,1);
//setup_ccp1(CCP_CAPTURE_RE);
setup_comparator(NC_NC_NC_NC);
setup_vref(FALSE);
//enable_interrupts(INT_CCP1);
enable_interrupts(GLOBAL);
}

[Fabricio]

sorry, i forget to kick on the wdt when I use delay_ms, now it is working correctly. the correct instruction is:
#use delay (clock=4000000, restart_wdt)

[PCM programmer]

Do you believe that this code works ?

[Fabricio]

the compiler does not generate error, nevertheless, now I am not using this piece of code.
The data sheet recommends to read “PIC12F6XX/16F6XX Memory Program-ming Specification” (DS41204). I have not read this yet.
For what I understand, only it is possible to have access to this direction during the programming.

[PCM programmer]

The data sheet says this: