 |
 |
| View previous topic :: View next topic |
| Author |
Message |
Eldert Besseling
Joined: 07 Oct 2003
Posts: 7
|
| display driver |
 Posted: Mon Apr 26, 2004 4:37 am |
 |
|
Hi All,
I am searching for drivers for the winstar WG12864F-YYH-V display
This is a LCD display with a character generator T6963C
Has somebody drivers written for it?
Regards
Eldert |
|
 |
treitmey
Joined: 23 Jan 2004
Posts: 1094
Location: Appleton,WI USA
|
|
| Posted: Mon Apr 26, 2004 10:20 am |
|
|
Yup, did this one too.
I wish we could have a file pile for code snipets and drivers.
Take it for what its worth. I'm not sure how complete it is.
I just mod a different graphics LCD driver.
| Code: |
/////////////////////////////////////////////////////////////////////////
//// c:\program files\PICC\drivers\LCD_T6963C.c ////
//// This file contains drivers for using a Tosiba T6963C controller ////
//// in parallel/8080(intel) mode. The T6963C is 240 pixles across ////
//// and 64 pixels down. The driver treats the upper left pixel 0,0 ////
//// ////
//// glcd_init(mode) ////
//// glcd_pixel(x,y,color) ////
//// glcd_line(x1,y1,x2,y2,color) ////
//// glcd_rect(x1,y1,x2,y2,fill,color) ////
//// glcd_bar(x1,y1,x2,y2,width,color) ////
//// glcd_circle(x,y,radius,fill,color) ////
//// glcd_text57(x,y,textptr,size,color) ////
//// glcd_fillScreen(color) ////
/////////////////////////////////////////////////////////////////////////
#ifndef GLCD_COL
#define GLCD_COL 240 // Used for text wrapping by glcd_text57 function and sanity check
#endif
#ifndef GLCD_ROW
#define GLCD_ROW 64 // Used for text wrapping by glcd_text57 function and sanity check
#endif
#define ON 1
#define OFF 0
#define YES 1
#define NO 0
#define set_tris_lcd(x) set_tris_a(0);set_tris_d(x)
//TRIS DataBus=x, note:control bus (PORTA) always outputs
////////////////////[PICK ONE OF THESE TWO SECTIONS]//////////////////
//const int1 LCDFont = 0;//Font select
//const int16 TextHome =0x0780;
//const int8 AreaSet_T =0x001E;//how many bytes before a new line
//const int16 GraphicsHome=0x0000;
//const int8 AreaSet_G =0x001E;//how many bytes before a new line
//////////////////////////////////////////////////////////////////////
const int1 LCDFont = 1;//Font select
const int16 TextHome =0x0780;
const int8 AreaSet_T =30;//how many bytes before a new line
const int16 GraphicsHome=0x0000;
const int8 AreaSet_G =0x001E;//how many bytes before a new line
////////////////////////////////////////////////////////////////
const int8 AutoModeWrite=0xB0;
const int8 AutoModeRead =0xB1;
const int8 AutoModeReset=0xB2;
const int8 LCDModeSet = 0x80;//send this OR'd with the following
const int8 LCDMode_OR = 0b0000;
const int8 LCDMode_XOR = 0b0001;
const int8 LCDMode_AND = 0b0010;
const int8 LCDMode_TA = 0b0100; //TEXT ATTRIBUTE mode.
const int8 LCDMode_RAM = 0b1000; //1=CG RAM, 0=internal CG ROM
const int8 LCDSetCursorPtr =0x21; //Number of lines in the cursor
const int8 LCDSetCursorSize=0xA0; //Number of lines in the cursor
const int8 LCDDispMode = 0x90;//send this OR'd with the following
const int8 LCDDisp_BLK = 0b0001;
const int8 LCDDisp_CUR = 0b0010;
const int8 LCDDisp_TXT = 0b0100;
const int8 LCDDisp_GRH = 0b1000;
const int8 LCDMaxBusyCount =20;//will try count-1 times before giving up
struct lcd_pin_def
{
BOOLEAN w_bar; // A0 Write bar active low
BOOLEAN r_bar; // A1 Read bar active low
BOOLEAN ce_bar; // A2 Chip Enable BAR active low
BOOLEAN cd; // A3 Command/Data BAR 1=command 0=data
BOOLEAN reset_bar; // A4 Reset active low
BOOLEAN fs; // A5 Font select
BOOLEAN unused1; // A6 Unused
BOOLEAN unused2; // A7 Unused
int unused4 : 8; // PortB... waisted some bits/bytes for clarity
int unused5 : 8; // PortC... waisted some bits/bytes for clarity
int data : 8; // PortD=Data bus
};
struct lcd_pin_def LCD;
#if defined(__PCM__)
#byte LCD = 5 //(no semicolin) 5=A0 on a 16F877A
#elif defined(__PCH__)
#byte LCD = 3968 //(no semicolin)3968=A0 on a 18F452
#endif
void glcd_FontSelect(int1 fs);
BYTE glcd_ReadByte();
int1 glcd_WriteByte(int1 cd, BYTE data); //return, 1=success 0=failure
int1 glcd_WriteByteAuto(BYTE data); //return, 1=success 0=failure
int1 glcd_WriteCmd2(int16 data, BYTE cmd);
int1 glcd_WriteCmd1(BYTE data, BYTE cmd);
//BOOLEAN glcd_pixel(unsigned int x,unsigned int y, int1 color);
//void glcd_fillScreen(int1 color);
void glcd_init(int1 mode) //init is the only function changed
{
int16 counter;
fprintf(DEBUG,"LCD init\r");
set_tris_lcd(0xff);//TRIS DATA bus,note:control bus always outputs
LCD.w_bar=1; // INITIAL STATES OF CONTROL PINS
LCD.r_bar=1; //
LCD.ce_bar=0; //
LCD.cd=1; // data
LCD.fs=LCDFont; // FontSelect
LCD.reset_bar=0; // preform a reset
delay_us(2); // delay the prescribed time for a reset
LCD.reset_bar=1; // run
//Set up the graphics and text areas
glcd_WriteCmd2(TextHome,0x40);
glcd_WriteCmd2(AreaSet_T,0x41);
glcd_WriteCmd2(GraphicsHome,0x42);
glcd_WriteCmd2(AreaSet_G,0x43);
//Clear all RAM of LCD
glcd_WriteByte(1,AutoModeWrite);
for (counter=0;counter<0xffff;++counter)
{
glcd_WriteByteAuto(0);//fill everything with zeros
}
glcd_WriteByte(1,AutoModeReset);
fprintf(DEBUG,"LCD init DONE.\r");
}
// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - //
// Purpose: Writes a byte of data from the current location
// Inputs: cd 1=command 0=data BYTE data
// Ouputs: Int1 1=success 0=failure
// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - //
int1 glcd_WriteByte(int1 cd, BYTE data)
{
BYTE status=0,count=0;
set_tris_lcd(0xFF);
LCD.w_bar=1;LCD.r_bar=1;LCD.cd=1;LCD.fs=LCDFont;//defaults
WriteByteLabel:
// First section checks if LCD is busy
LCD.r_bar=0; // Read
status=LCD.data; // Latch data
LCD.r_bar=1; // Release
++count;
if (count>LCDMaxBusyCount)
{
fprintf(DEBUG,"-Error writing to LCD,.. Busy\r");
return(0);
}
if (!bit_test(status,0) || !bit_test(status,1)) //loop if either is 0
{
goto WriteByteLabel;
}
//if(cd==0) {fprintf(DEBUG,"Data= %lx\r",data);}
//if(cd==1) {fprintf(DEBUG,"Command %lx\r",data);}
set_tris_lcd(0x00); //All outputs
LCD.cd=cd; //Command/Data bar
LCD.data=data;
LCD.r_bar=1; //not read
LCD.w_bar=0; //write
set_tris_lcd(0xFF); //Port D tristate ie: all inputs
return (1); //Return status
}
// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - //
// Purpose: Writes continuous bytes of data from the current location
// Inputs: BYTE data
// Ouputs: Int1 1=success 0=failure
// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - //
int1 glcd_WriteByteAuto(BYTE data)
{
BYTE status=0,count=0; //status bits ARE DIFFERENT BITS THAN NORMAL
set_tris_lcd(0xFF); //First section checks if LCD is busy
LCD.w_bar=1;LCD.r_bar=1;LCD.cd=1;LCD.fs=1;//defaults
do
{
LCD.r_bar=0; // Read
status=LCD.data; // Latch data
LCD.r_bar=1; // Release
++count;
if (count>LCDMaxBusyCount)
{
fprintf(DEBUG,"0Error writing to LCD,.. Busy status=%x\r",status);
return(0);
}
}while (!bit_test(status,3));//Check until bit3==1 (ready)
set_tris_lcd(0x00); //All outputs
LCD.cd=0; //This is always data, cd=0
LCD.data=data; //Put data on data bus
LCD.r_bar=1; //not read
LCD.w_bar=0; //write
LCD.w_bar=1; //release
set_tris_lcd(0xFF); //Port D tristate ie: all inputs
return (1); //Return status
}
// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - //
// Purpose: Writes a one byte of data and a command
// Inputs: BYTE data BYTE cmd
// Ouputs: Int1 1=success 0=failure
// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - //
int1 glcd_WriteCmd1(BYTE data, BYTE cmd)
{
if (!glcd_WriteByte(0,data)){
fprintf(DEBUG,"2Error LCD is Busy\r");
return (0);
}
if (!glcd_WriteByte(1,cmd)){
fprintf(DEBUG,"3Error LCD is Busy\r");
return (0);
}
return (1);
}
// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - //
// Purpose: Writes a two data byte command
// Inputs: int16 data BYTE cmd
// Ouputs: Int1 1=success 0=failure
// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - //
int1 glcd_WriteCmd2(int16 data, BYTE cmd)
{
if (!glcd_WriteByte(0,data & 0xFF)){
fprintf(DEBUG,"1Error LCD is Busy\r");
return (0);
}
if (!glcd_WriteByte(0,data>>8)){
fprintf(DEBUG,"2Error LCD is Busy\r");return (0);
}
if (!glcd_WriteByte(1,cmd)){
fprintf(DEBUG,"3Error LCD is Busy\r");
return (0);
}
return (1);
}
// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - //
// Purpose: Reads a byte of data from the current location
// Ouputs: A byte of data read from the LCD
// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - //
BYTE glcd_ReadByte()
{
BYTE data,status,count=0; // Stores the data read from the LCD
set_tris_lcd(0xFF) ; //First section checks if LCD is busy
LCD.w_bar=1;LCD.r_bar=1;LCD.cd=1;LCD.fs=LCDFont;//defaults
LCD.cd=0;
ReadByteLabel:
LCD.r_bar=0; // Read
status=LCD.data; // Latch data
LCD.r_bar=1; // Release
++count;
if (count>LCDMaxBusyCount)
{
fprintf(DEBUG,"-Error writing to LCD,.. Busy\r");
return(0);
}
if (!bit_test(status,0) || !bit_test(status,1)) //loop if either is 0
{
// fprintf(DEBUG,".");
goto ReadByteLabel;
}
LCD.cd=0; // Command/Data bar
LCD.r_bar=0; // read
data=LCD.data;
LCD.r_bar=1;
return data; //Return the read data
}
// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - //
// Purpose: Sends data to LCD
// Ouputs: A byte of data read from the LCD
// - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - //
void glcd_putc( char c) {
//fprintf(DEBUG,"->%x\r",c);
switch (c) {
// case '\f' : lcd_send_byte(0,1);
// delay_ms(2);
// break;
// case '\n' : lcd_gotoxy(1,2); break;
// case '\b' : lcd_send_byte(0,0x10); break;
default : glcd_WriteCmd1(c-0x20,0xc0);break;//Write to LCD autoinc
}
}
|
|
|
|
xmen
Joined: 30 Jul 2004
Posts: 2
|
|
| Posted: Fri Jul 30, 2004 9:23 pm |
|
|
Hello Treitmey:
In your source code, there are a lot of functions that are not in source code.
Concretely, are not:
glcd_pixel(x,y,color)
glcd_line(x1,y1,x2,y2,color)
glcd_rect(x1,y1,x2,y2,fill,color)
glcd_bar(x1,y1,x2,y2,width,color)
glcd_circle(x,y,radius,fill,color)
glcd_text57(x,y,textptr,size,color)
glcd_fillScreen(color)
May you provide full source code, please ?
Regards.
====== |
|
|
dyeatman
Joined: 06 Sep 2003
Posts: 1933
Location: Norman, OK
|
|
| Posted: Sat Jul 31, 2004 12:40 pm |
|
|
Treitmey,
You can put it in the code library... For us thats the "file pile"
 |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
FAQ 
Search
Register
Profile 
Log in to check your private messages 
Log in
