CCS :: View topic - Error with 18F4620: Expecting a structure/union

FAQ

Forum Help

Official CCS Support

Profile Log in to check your private messages Log in

CCS does not monitor this forum on a regular basis.

Please do not post bug reports on this forum. Send them to CCS Technical Support

Error with 18F4620: Expecting a structure/union

CCS Forum Index -> General CCS C Discussion

View previous topic :: View next topic

Author

Message

Knight_FlyCn

Joined: 10 May 2013
Posts: 16
Location: Việt Nam

Error with 18F4620: Expecting a structure/union

Posted: Fri May 10, 2013 11:00 am

Code:

/* _CPUDIV_OSC1_PLL2_1L, // Divide clock by 2
_FOSC_HS_1H, // Select High Speed (HS) oscillator
_WDT_OFF_2H, // Watchdog Timer off
MCLRE_ON_3H // Master Clear on
*/

#include <RFD.h>
#include "def_18f4620.c"
#include "slave_1_tx_rx.h"

// Xac dinh ----
#use rs232(baud=9600,parity=N,xmit=PIN_C6,rcv=PIN_C7,bits=8)
#define SPI_MODE_0 (SPI_L_TO_H | SPI_XMIT_L_TO_H)
// Them vao
#ifndef FREQ
#define FREQ 4000000
#ifndef baud
#define baud 96000
#define spbrg_value (((FREQ/64)/baud)-1)
//
#bit CS = 0xF80.4
#bit RST = 0xF82.2
#bit INT_ = 0xF81.0
#bit WAKE = 0xF82.1

#bit CS_Direction = 0xF92.4
#bit RST_Direction = 0xF94.2
#bit INT_Direction = 0xF93.0
#bit WAKE_Direction = 0xF94.1

///////////////////////////////////////////////////////////////////////////////
// Command: 0x00: IP request //
// 0x01: I_AM_LM35 //
// 0x02: I_AM_PIR
INT TEMP;
int adress;
INT VALUE;
INT16 k=0;
const int IP_request=0x00,adress_surport=0x01,ip_surport=0x10;
int I_AM_LM35=0x01;
INT DATA_SEND=0X02;
INT COMMAND;//
INT1 IP_REQUEST_FLAG=FALSE;
SHORT SLEEP_MODE=true;

//!#INT_RTCC
//!VOID NGAT_TIMER0()
//!{ printf("ngat timer0!");
//! ++;
//! IF (k>= 1000)
//! {
//! k=0;
//! SLEEP_MODE=FALSE;
//! }
//! TMR0IF=0;
//! disable_interrupts(INT_TIMER0);
//!}
//!

#INT_EXT
void ngat_RB0()
{
temp = read_ZIGBEE_short(INTSTAT); // Read and flush register INTSTAT
if ((temp&(1<<3))==(1<<3))
{
read_RX_FIFO();

COMMAND =DATA_RX[0];
SWITCH (COMMAND)
{
CASE ip_surport:
ADRESS=DATA_RX[1];
rfd_ADDRESS_short[1]=adress;
IP_REQUEST_FLAG=TRUE;
BREAK;
break;
}

}

}

void main()
{
TRISB1=TRISB2=TRISB3=1;
TRISC0=TRISD3=0;

CS_Direction = 0; // Set direction to be output
RST_Direction = 0; // Set direction to be output
INT_Direction = 1; // Set direction to be input
WAKE_Direction = 0; // Set direction to be output

Delay_ms(5);
setup_spi(SPI_MASTER | SPI_MODE_0 | SPI_CLK_DIV_4); // Initialize SPI module
pin_reset(); // Activate reset from pin
software_reset(); // Activate software reset
RF_reset(); // RF reset
set_WAKE_from_pin(); // Set wake from pin
set_long_address(ADDRESS_long_1);
set_short_address(rfd_ADDRESS_short); // Set short address
set_PAN_ID(PAN_ID); // Set PAN_ID

init_ZIGBEE_nonbeacon(); // Initialize ZigBee module
nonbeacon_device();
set_TX_power(31); // Set max TX power
set_frame_format_filter(1); // 1 all frames, 3 data frame only
set_reception_mode(1); // 1 normal mode
enable_int();
pin_wake(); // Wake from pin

//enable interrupt ext
enable_interrupts(GLOBAL);
enable_interrupts(INT_EXT);
ext_int_edge(H_to_L);
// gioi thieu
printf("****************************************\r\n");
Printf(" ");
Printf(" RFD_designed by Huynh Thanh Dien\r\n");
Printf(" ");
printf("****************************************\r\n");

// IP request
printf(" Requesting IP...\r\n");

PAN_ID_destination[0] = PAN_ID[0];
PAN_ID_destination[1] = PAN_ID[1];
address_short_destination[0] = coord_address_short[0];
address_short_destination[1] = coord_address_short[1];
PAN_ID_source[0] = PAN_ID[0];
PAN_ID_source[1] = PAN_ID[1];
address_short_source[0] = rfd_address_short[0];
address_short_source[1] = rfd_address_short[1];
DATA_TX[0]=Ip_request;
DATA_TX[1]=0X00;
write_TX_normal_FIFO();
WHILE (!IP_REQUEST_FLAG){}
set_short_address(rfd_ADDRESS_short);
IP_REQUEST_FLAG=FALSE;
PRINTF(" IP REQUEST SUCCESSED!\r\n");
PRINTF(" MY IP_ADRESS IS: 0x0%D\r\n",ADRESS);

DATA_TX[0]=I_AM_LM35;
DATA_TX[1]=0X00;
write_TX_normal_FIFO();

//SETUP ADC
setup_adc_ports( ALL_ANALOG );
setup_adc(ADC_CLOCK_INTERNAL );
set_adc_channel( 0 );

while (1)
{
value = read_adc();
VALUE=VALUE*360/1023;
PRINTF(" NHIET DO: %D\r\n",VALUE);
DATA_TX[0]=DATA_SEND;
DATA_TX[1]=VALUE;
write_TX_normal_FIFO();
//! IF (SLEEP_MODE)
//! {
//! printf(" Sleeping...");
//! SLEEP_MODE=TRUE;
//! sleep();
//! }

delay_ms(1000);
}

}

When I add:

Code:

SPBRG=spbrg_value;    // Fill SPBRG register to set the baud rate
RCSTA.SPEN=1;       // To activate serial port (Tx and Rx pins)
RCSTA.CREN=1;       // To enable continuous reception
PIE1.RCIE=1;       // To enable the Reception (Rx) Interrupt
INTCON.GIE=1;
INTCON.PEIE=1;

CCS 4.1 errors : "Expecting a structure/union"

Who can help me repair it.
_________________
Thinh

Knight_FlyCn

Joined: 10 May 2013
Posts: 16
Location: Việt Nam

Posted: Fri May 10, 2013 11:51 am

I success

Code:

/* _CPUDIV_OSC1_PLL2_1L, // Divide clock by 2
_FOSC_HS_1H, // Select High Speed (HS) oscillator
_WDT_OFF_2H, // Watchdog Timer off
MCLRE_ON_3H // Master Clear on
*/

#include <RFD.h>
#include "def_18f4620.c"
#include "slave_1_tx_rx.h"

// Xac dinh ----
#use rs232(baud=9600,parity=N,xmit=PIN_C6,rcv=PIN_C7,bits=8)
#define SPI_MODE_0 (SPI_L_TO_H | SPI_XMIT_L_TO_H)
// Them vao
#ifndef FREQ
#define FREQ 4000000
#ifndef baud
#define baud 96000
#define spbrg_value (((FREQ/64)/baud)-1)
//
#bit CS = 0xF80.4
#bit RST = 0xF82.2
#bit INT_ = 0xF81.0
#bit WAKE = 0xF82.1

#bit CS_Direction = 0xF92.4
#bit RST_Direction = 0xF94.2
#bit INT_Direction = 0xF93.0
#bit WAKE_Direction = 0xF94.1

///////////////////////////////////////////////////////////////////////////////
// Command: 0x00: IP request //
// 0x01: I_AM_LM35 //
// 0x02: I_AM_PIR
INT TEMP;
int adress;
INT VALUE;
INT16 k=0;
const int IP_request=0x00,adress_surport=0x01,ip_surport=0x10;
int I_AM_LM35=0x01;
INT DATA_SEND=0X02;
INT COMMAND;//
INT1 IP_REQUEST_FLAG=FALSE;
SHORT SLEEP_MODE=true;

// Them vao
unsigned char card_id[10];
unsigned int i=0,pos;
//

//!#INT_RTCC
//!VOID NGAT_TIMER0()
//!{ printf("ngat timer0!");
//! ++;
//! IF (k>= 1000)
//! {
//! k=0;
//! SLEEP_MODE=FALSE;
//! }
//! TMR0IF=0;
//! disable_interrupts(INT_TIMER0);
//!}
//!

#INT_EXT
void ngat_RB0()
{
temp = read_ZIGBEE_short(INTSTAT); // Read and flush register INTSTAT
if ((temp&(1<<3))==(1<<3))
{
read_RX_FIFO();

COMMAND =DATA_RX[0];
SWITCH (COMMAND)
{
CASE ip_surport:
ADRESS=DATA_RX[1];
rfd_ADDRESS_short[1]=adress;
IP_REQUEST_FLAG=TRUE;
BREAK;
break;
}

}

}
void interrupt()
{
card_id[i]=RCREG; // Store the received data byte by byte
i++;
}

void main()
{
TRISB1=TRISB2=TRISB3=1;
TRISC0=TRISD3=0;

CS_Direction = 0; // Set direction to be output
RST_Direction = 0; // Set direction to be output
INT_Direction = 1; // Set direction to be input
WAKE_Direction = 0; // Set direction to be output

Delay_ms(5);
setup_spi(SPI_MASTER | SPI_MODE_0 | SPI_CLK_DIV_4); // Initialize SPI module
pin_reset(); // Activate reset from pin
software_reset(); // Activate software reset
RF_reset(); // RF reset
set_WAKE_from_pin(); // Set wake from pin
set_long_address(ADDRESS_long_1);
set_short_address(rfd_ADDRESS_short); // Set short address
set_PAN_ID(PAN_ID); // Set PAN_ID

init_ZIGBEE_nonbeacon(); // Initialize ZigBee module
nonbeacon_device();
set_TX_power(31); // Set max TX power
set_frame_format_filter(1); // 1 all frames, 3 data frame only
set_reception_mode(1); // 1 normal mode
enable_int();
pin_wake(); // Wake from pin

//enable interrupt ext
enable_interrupts(GLOBAL);
enable_interrupts(INT_EXT);
ext_int_edge(H_to_L);
// gioi thieu
printf("****************************************\r\n");
Printf(" ");
Printf(" RFD_designed by Huynh Thanh Dien\r\n");
Printf(" ");
printf("****************************************\r\n");

// IP request
printf(" Requesting IP...\r\n");

PAN_ID_destination[0] = PAN_ID[0];
PAN_ID_destination[1] = PAN_ID[1];
address_short_destination[0] = coord_address_short[0];
address_short_destination[1] = coord_address_short[1];
PAN_ID_source[0] = PAN_ID[0];
PAN_ID_source[1] = PAN_ID[1];
address_short_source[0] = rfd_address_short[0];
address_short_source[1] = rfd_address_short[1];
DATA_TX[0]=Ip_request;
DATA_TX[1]=0X00;
write_TX_normal_FIFO();
WHILE (!IP_REQUEST_FLAG){}
set_short_address(rfd_ADDRESS_short);
IP_REQUEST_FLAG=FALSE;
PRINTF(" IP REQUEST SUCCESSED!\r\n");
PRINTF(" MY IP_ADRESS IS: 0x0%D\r\n",ADRESS);

DATA_TX[0]=I_AM_LM35;
DATA_TX[1]=0X00;
write_TX_normal_FIFO();

////////////////////////////////////////////////////////////////////////////

// SET RX VA TX
SPBRG=spbrg_value; // Fill SPBRG register to set the baud rate
SPEN=1; // To activate serial port (Tx and Rx pins)
CREN=1; // To enable continuous reception
RCIE=1; // To enable the Reception (Rx) Interrupt
GIE=1;
PEIE=1;

while (1)
{
interrupt();
PRINTF(" MA SO THE: %D\r\n",card_id[10]);
DATA_TX[0]=DATA_SEND;
DATA_TX[1]=card_id[10];
write_TX_normal_FIFO();
//! IF (SLEEP_MODE)
//! {
//! printf(" Sleeping...");
//! SLEEP_MODE=TRUE;
//! sleep();
//! }

delay_ms(1000);
}

}

-------------------------------------------
Compile success
-------------------------------------------

People watching and commenting. RX pins of the 18F4620 connected to the RFID reader and read key tag . Save to "ard_id". And sent to the ZigBee module
_________________
Thinh

senur

Joined: 11 Dec 2013
Posts: 13


Posted: Wed Dec 11, 2013 9:33 am

I'm facing the same problem. May I know what you did?

Display posts from previous:

	CCS Forum Index -> General CCS C Discussion	All times are GMT - 6 Hours
Page 1 of 1

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum