 |
 |
| View previous topic :: View next topic |
| Author |
Message |
zmtek
Joined: 19 Jan 2013
Posts: 5
|
| pic 16LF1825 brownout reset when wake up |
 Posted: Mon Feb 18, 2013 7:40 am |
 |
|
Hi,
I am running following code to wake up from sleep when receiving char
over rs232 on 16F1825 and it is running fine, when programmed
same code to 16LF1825 a brownout reset occuring instead of wake up.
Everything is same - board design, power, hex etc...
the only difference is 16F1825 is DIP package and 16LF1825 is QFN.
the same occurs when i use change on PORT A interrupt for wake
up source.
Any ideas?
| Code: |
#include <16LF1825.h>
#FUSES INTRC_IO,NOWDT,NOPUT,NOMCLR,NOPROTECT,NOCPD,BROWNOUT_NOSL,NOCLKOUT,NOIESO,NOFCMEN,NOSTVREN,BORV19,NODEBUG,NOLVP
#use delay(clock=16000000)
#use rs232 (baud=9600,parity=N,bits=8,xmit=PIN_c4, rcv=PIN_c5)
#bit WUE_BIT=GETENV("BIT:WUE")
int8 dummy=0;
int8 stat=0;
void main(void)
{
SETUP_DAC(dac_off);
setup_comparator (nc_nc_nc_nc);
setup_adc(ADC_OFF);
setup_adc_ports(NO_ANALOGS);
setup_ccp1(ccp_off);
setup_vref(VREF_OFF);
setup_spi(SPI_DISABLED );
SETUP_WDT(WDT_OFF);
port_a_pullups(false);
port_c_pullups(false);
delay_ms(100);
stat=RESTART_CAUSE();
printf("Startup reset=%02X\r\n",stat);delay_ms(10);
setup_timer_0 (RTCC_INTERNAL | RTCC_DIV_8);
//setup_timer_1(T1_EXTERNAL | T1_DIV_BY_1 |T1_ENABLE_T1OSC);
//setup_timer_1(T1_DISABLED);
setup_timer_2(T2_DISABLED,0,1);
//setup_timer_3(T3_DISABLED|T3_DIV_BY_1);
set_tris_a(0b00000000);
set_tris_c(0b00100000);
output_high(PIN_A0); output_high(PIN_A1); output_high(PIN_A2);
output_high(PIN_A3); output_high(PIN_A4); output_high(PIN_A5);
output_high(PIN_c0); output_high(PIN_c1); output_high(PIN_c2);
output_high(PIN_c3); output_high(PIN_c4); output_float(PIN_c5);
enable_interrupts(global);
while(1)
{
WUE_BIT=1;
clear_interrupt(int_rda); enable_interrupts(int_rda);
sleep(); delay_cycles(1);
printf("\r\nwake up\r\n");delay_ms(100);
}
} //end of main()
#int_RDA
RDA_isr()
{
dummy=getc();
} |
|
|
 |
jeremiah
Joined: 20 Jul 2010
Posts: 1345
|
|
| Posted: Mon Feb 18, 2013 3:41 pm |
|
|
| The LF chip has some low power settings that the F chip does not. I would start there and see if any of the defaults would cause your problem. Also, what voltage are you operating the PIC at? |
|
|
zmtek
Joined: 19 Jan 2013
Posts: 5
|
|
| Posted: Mon Feb 18, 2013 4:02 pm |
|
|
i am running it 3.3v down to 2.5V.. I searched data sheet and errdata but
can not find any setting related to LF version :( |
|
|
PCM programmer
Joined: 06 Sep 2003
Posts: 21708
|
|
| Posted: Mon Feb 18, 2013 6:48 pm |
|
|
I looked in the errata sheet for the 16LF1825 and there's nothing on
brownout. I also checked all the older revisions of the errata and
there's nothing either.
But it still really sounds like an errata. So I kept checking. I found this
post on the Microchip forum, which is for a PIC in the same family:
http://www.microchip.com/forums/m591855.aspx
I think this errata is what you have. Here's the errata sheet for
the 16LF1826. Read the section on Brownout:
http://ww1.microchip.com/downloads/en/DeviceDoc/80485K.pdf
It also affects the "Brownout Nosleep" mode. It lists some work-arounds
that you can try.
If you can confirm that it's the same errata, you should report it to
Microchip so they can add it to the 16LF1825 errata sheet. |
|
|
zmtek
Joined: 19 Jan 2013
Posts: 5
|
|
| Posted: Thu Feb 21, 2013 10:44 am |
|
|
The solution in 16f1826 errata works (I switched to brownout_sw and switch off brownout before entering sleep mode). Thank you!
I posted the problem in Microchip official forum and I hope they will update the errata.
Best regards |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
FAQ 
Search
Register
Profile 
Log in to check your private messages 
Log in
