 |
 |
 FAQ Forum Help Official CCS Support  Search
 Register
 Profile  Log in to check your private messages  Log in
|
CCS does not monitor this forum on a regular basis. Please do not post bug reports on this forum. Send them to CCS Technical Support |
| Search found 16 matches |
| Author | Message |
|---|---|
 Topic: DMX problems receiving characters |
|
| spradecom.rnd Replies: 5 Views: 6440 |
 Forum: General CCS C Discussion Posted: Wed Aug 11, 2010 12:13 am Subject: DMX receiving problem |
| I wrote a code like the others based on Mark's code found in this forum, following the same ideas, but it doesn't work. The first problem is that the usart never generates a FERR error to detect the b ... | |
| Topic: DMX Receiver using Mark's code |
|
| spradecom.rnd Replies: 5 Views: 10267 |
Forum: General CCS C Discussion Posted: Sat Aug 07, 2010 12:27 am Subject: Problem with DMX receive code |
| I am new to CCS and also microcontroller. I have taken help from MARKs DMX receiver. But my code is not working. Can anybody tell me where I am making mistake? I am using PIC16F1938. CCS v4.108. I am ... | |
| Topic: DMX, couldn't get FERR, couldn't run INT_RDA |
|
| spradecom.rnd Replies: 3 Views: 5194 |
Forum: General CCS C Discussion Posted: Thu Aug 05, 2010 4:38 am Subject: DMX, couldn't get FERR, couldn't run INT_RDA |
| Can any one send me working DMX receiver code. I am using PIC16F1938. I have tried several routine but no use. email [email protected] | |
| Topic: How to set the calibration value for PIC10F22x |
|
| spradecom.rnd Replies: 6 Views: 8437 |
Forum: General CCS C Discussion Posted: Thu Apr 29, 2010 3:13 am Subject: How to set the calibration value for PIC10F22x |
| I have checked setting. There is nothing I could figure out. I have checked the setting also. As soon as I power my board the chip goes in reset mode. MCLR high, ICSPCLK high, AN0 low but ADC value ma ... | |
| Topic: How to set the calibration value for PIC10F22x |
|
| spradecom.rnd Replies: 6 Views: 8437 |
Forum: General CCS C Discussion Posted: Wed Apr 28, 2010 8:45 am Subject: How to set the calibration value for PIC10F22x |
| I have upgraded to version 4.104. The adc_on definition is present in the header. But after loading the program the adc value always remains high. MCLR pin always high, ICSPCLK pin always high. AN0 lo ... | |
| Topic: Problem with PIC10f222 |
|
| spradecom.rnd Replies: 15 Views: 21906 |
Forum: General CCS C Discussion Posted: Wed Apr 28, 2010 5:31 am Subject: Problem with PIC10f222 |
| The ADC value always remains high even if not input is given. the Pin shows zero voltage. then how the value in ADRESH is always high | |
| Topic: How to set the calibration value for PIC10F22x |
|
| spradecom.rnd Replies: 6 Views: 8437 |
Forum: General CCS C Discussion Posted: Wed Apr 28, 2010 3:16 am Subject: How to set the calibration value for PIC10F22x |
| I am using version 4.84. what is the solution for the setup_adc(ADC_ON);
I have tried setup_adc(true); but the adc value always remains 255 or max even if input is zero |
|
| Topic: Problem with PIC10f222 |
|
| spradecom.rnd Replies: 15 Views: 21906 |
Forum: General CCS C Discussion Posted: Wed Apr 28, 2010 1:59 am Subject: Problem with PIC10f222 |
| Sir,
we are assigning AN0 as a analog input. But it always remains high. Is it that the ICSPDAT pin is continuous high. What steps to do to work pin no 1 as analog input after programming ? ... |
|
| Topic: Problem with PIC10f222 |
|
| spradecom.rnd Replies: 15 Views: 21906 |
Forum: General CCS C Discussion Posted: Wed Apr 28, 2010 1:16 am Subject: Problem with PIC10f222 |
| thank you very much sir, now changing ic and removing holding from reset worked | |
| Topic: Problem with PIC10f222 |
|
| spradecom.rnd Replies: 15 Views: 21906 |
Forum: General CCS C Discussion Posted: Wed Apr 28, 2010 1:04 am Subject: Problem with PIC10f222 |
| Sir,
can you send a hex file for the program you build which toggles LED at pin 1. email id - [email protected] If your hex works then there is problem in the compiler or our hardware se ... |
|
| Topic: Problem with PIC10f222 |
|
| spradecom.rnd Replies: 15 Views: 21906 |
Forum: General CCS C Discussion Posted: Wed Apr 28, 2010 12:40 am Subject: Problem with PIC10f222 |
| 5.05V output from 7805. The IC is PIC10F222 E/OT 6-pin sot-23 | |
| Topic: Problem with PIC10f222 |
|
| spradecom.rnd Replies: 15 Views: 21906 |
Forum: General CCS C Discussion Posted: Wed Apr 28, 2010 12:20 am Subject: Problem with PIC10f222 |
| I have changed the code . This is the new lst file.Even then it is not working.
I have also replaced the IC.and checked.Everytime all the pins except GND(Pin no2) shows high. I tried the same code of ... |
|
| Topic: Problem with PIC10f222 |
|
| spradecom.rnd Replies: 15 Views: 21906 |
Forum: General CCS C Discussion Posted: Tue Apr 27, 2010 11:24 pm Subject: Problem with PIC10f222 |
| I tried to program. but the same result. Here is the list file
CCS PCB C Compiler, Version 4.084, 36728 28-Apr-10 10:54 Filename: main.lst ... |
|
| Topic: Problem with PIC10f222 |
|
| spradecom.rnd Replies: 15 Views: 21906 |
Forum: General CCS C Discussion Posted: Tue Apr 27, 2010 10:20 pm Subject: Problem with PIC10f222 |
| even trying set_options(value) code doesnt work. what to do please help | |
| Topic: Problem with PIC10f222 |
|
| spradecom.rnd Replies: 15 Views: 21906 |
Forum: General CCS C Discussion Posted: Tue Apr 27, 2010 9:55 pm Subject: Problem with PIC10f222 |
| I am using ICD-2 | |
All times are GMT - 6 Hours |
Powered by phpBB © 2001, 2005 phpBB Group